CS14 PERFORMANCE SPECIFICATIONS
Depth capacity coring (wireline or conventional)
B wireline 1540 m (5052 ft)
N wireline 1200 m (4042 ft)
H wireline 800 m (2695 ft)
P wireline 475 m (1558 ft)
Depth are based on vertical hole
Main hoist
Single line capacity: Bare drum 80 kN (18 000 lb)
Line speed: Bare drum 44 m/min (148 ft/min)
Cable size: 35 m (118 ft) x 16 mm (10/16 in)
Wireline
Capacity: 1830 m (6000 ft) of 4,76 mm (3/16 in)
975 m (3200 ft) of 6,35 mm (1/4 in)
Line pull: bare drum: 11,9 kN (2665 lb)
full drum: 3,0 kN (668 lb)
Line speed: bare drum 114 m/min (374 ft/min)
full drum 453 m/min (1486 ft/min)
Mast and feed system
Feed travel: 3,5 m (11,5 ft)
Feed speeds: fast and slow with variable control
Thrust: 59,6 kN (13 390 lb)
Pull: 138 kN (31 020 lb)
Drilling angle: 45 to 90 degrees
Rod pull length: 6,09 m (20 ft)
Power unit
Manufacture: Caterpillar
Model: CAT C6.6, 6,6 liter 6 cylinder, Tier III
Power: 161 kW (216 hp)
RPM: 1800
Engine type: Diesel turbocharged/after cooled
Cooling: Water
Hydraulic system
Primary pump: 28 MPa – 242 l/min (4061 psi – 63,9 gal/min)
Secondary pump: 20 MPa – 122 l/min (2901 psi – 32,2 gal/min)
Auxiliary pump: 21,5 MPa – 47 l/min (3118 psi – 12,4 gal/min)
Hydraulic oil cooling: Air
Drillhead and spindle speeds
Power: hydraulic motor – variable speed/reversible
Final drive: 4 in chain driven in oil bath – 2,5 ratio
Spindle (inner diameter): 117 mm (4 5/8 in)
Spindle speeds:
Ratio Speed, rpm Torque, Nm (ftlb)
1st 6,63:1 117-196 5113-3051 (3771-2250)
2nd 3,17:1 245-410 2445-1459 (1803-1076)
3rd 1,72:1 451-756 1326-792 (978-584)
4th 1,00:1 776 1300 771-460 (569-340)
Range selection: manual control from operator’s station
Hinged head: swing away
v1.6
Chuck assembly
Type: hydraulic open, spring closed
Maximum inside diameter: 117 mm (4 5/8 in)
Holding capacity: 1 8143 kg (40 000 lb)
Drill base supports
Trailer mounted rig, four 770 mm (30,3 in) wheels
Support: 4 hydraulic jacks
Pad diameter: 200 / 230 mm (7,87 / 9 in)
Travel length: 550 mm (21,6 in)
Weight
CS14 incl. Trido140 and Rod Holder: 7000 kg (15 430 lb)
Dimensions (L – W – H)
In transport position (top mast removed):
6370 mm (21,45ft) 2200 mm (7,22ft) 2340 mm (7,88ft)
Transport on drill site (top mast folded):
6370 mm (21,45ft) 2550 mm (8,59ft) 2340 mm (7,88ft)
Standard equipment
-Hydraulic mast dump -Hydraulic mast raise
-Mast in two sections -4 hydraulic levelling jacks
-Large crown sheave wheel -Towing package
-Wear lines on lower mast -Fuel tank 200 l (53 gal)
-Safety guards -Fuel filter & water separator
-Hydraulic oil reservoir fill pump
& filtration
Options
-Hydraulic P-size rod holder -Hydraulic mud mixer
-Water flow meter (max 6,4 MPa) -RPM meter
-Hydraulic mud pump, Trido 140:
max flow: 140 l/min (37 gal/min)
max pressure: 7 MPa (1015 psi)
All weights and dimensions are approximations and are subject
to change